- ????????? 2007/03/03 12:19
- ????????? ぢる
<[email protected]>
-
玄箱HGでddclientの設定をしていたのですが、IPの自動更新がされずに困っています
ddclientのインストール自体はうまく行っているみたいなのですが、
# ddclient -daemon=0 -debug -verbose -noquiet
を実行すると、下のように帰ってきます
DEBUG: get_ip: using ip, ip reports <undefined>
WARNING: unable to determine IP address
これがddclientの設定なのかルータの設定によるものなのかが判別つかない状態です
ddclient.confは以下のとおり設定しています
######################################################################
##
## $Id: sample-etc_ddclient.conf 10 2006-06-14 19:59:31Z wimpunk $
##
## Define default global variables with lines like:
## var=value [, var=value]*
## These values will be used for each following host unless overridden
## with a local variable definition.
##
## Define local variables for one or more hosts with:
## var=value [, var=value]* host.and.domain[,host2.and.domain...]
##
## Lines can be continued on the following line by ending the line
## with a \
##
##
## Warning: not all supported routers or dynamic DNS services
## are mentioned here.
##
######################################################################
daemon=300 # check every 300 seconds
syslog=yes # log update msgs to syslog
#mail=root # mail all msgs to root
#mail-failure=root # mail failed update msgs to root
#pid=/var/run/ddclient.pid # record PID in file.
#ssl=yes # use ssl-support. Works with
# ssl-library
#
#use=watchguard-soho, fw=192.168.11.1:80 # via Watchguard's SOHO FW
#use=netopia-r910, fw=192.168.11.1:80 # via Netopia R910 FW
#use=smc-barricade, fw=192.168.11.1:80 # via SMC's Barricade FW
#use=netgear-rt3xx, fw=192.168.11.1:80 # via Netgear's internet FW
#use=linksys, fw=192.168.11.1:80 # via Linksys's internet FW
#use=maxgate-ugate3x00, fw=192.168.11.1:80 # via MaxGate's UGATE-3x00 FW
#use=elsa-lancom-dsl10, fw=10.0.0.254:80 # via ELSA LanCom DSL/10 DSL Router
#use=elsa-lancom-dsl10-ch01, fw=10.0.0.254:80 # via ELSA LanCom DSL/10 DSL Router
#use=elsa-lancom-dsl10-ch02, fw=10.0.0.254:80 # via ELSA LanCom DSL/10 DSL Router
#use=alcatel-stp, fw=10.0.0.138:80 # via Alcatel Speed Touch Pro
#use=xsense-aero, fw=192.168.11.1:80 # via Xsense Aero Router
#use=allnet-1298, fw=192.168.11.1:80 # via AllNet 1298 DSL Router
#use=3com-oc-remote812, fw=192.168.11.1:80 # via 3com OfficeConnect Remote 812
#use=e-tech, fw=192.168.11.1:80 # via E-tech Router
#use=cayman-3220h, fw=192.168.11.1:1080 # via Cayman 3220-H DSL Router
#
#fw-login=root, fw-password= # FW login and password
#
## To obtain an IP address from FW status page (using fw-login, fw-password)
#use=fw, fw=192.168.1.254/status.htm, fw-skip='IP Address' # found after IP Address
#
## To obtain an IP address from Web status page (using the proxy if defined)
#use=web, web=checkip.dyndns.org/, web-skip='IP Address' # found after IP Address
#
#use=ip, ip=192.168.11.150 # via static IP's
#use=if, if=eth0 # via interfaces
use=web # via web
#
#protocol=dyndns2 # default protocol
#proxy=fasthttp.sympatico.ca:80 # default proxy
#server=members.dyndns.org # default server
#server=members.dyndns.org:8245 # default server (bypassing proxies)
login=******** # default login
password=******* # default password
#mx=mx.for.your.host # default MX
#backupmx=yes|no # host is primary MX?
#wildcard=yes|no # add wildcard CNAME?
##
## dyndns.org dynamic addresses
##
## (supports variables: wildcard,mx,backupmx)
##
server=members.dyndns.org, \
protocol=dyndns2 \
******.homeftp.net
DynDNSへは登録済みです
何分、Linuxを触ったのがこれがはじめてなので右も左もわからない状態です
どなたかご教授いただければ幸いです
|
このスレッドはクローズされています。記事の閲覧のみとなります。
ddclientについて
Re: ddclientについて ( No.1 )